The AW-HR140 is an integrated remote camera system that incorporates an outdoor housing, camera, lens and pan-tilt head and maintains stable shooting performance in the toughest of environments. It is equipped with the same DSP and full HD 3MOS sensors as the AW-HE130 which results in high sensitivity, high S/N ratio, and high resolution due to its advanced video processing.
- Protection IP65
- 3MOS sensor (same as AW-HE130)
- 20x Optical Zoom (plus 1.4x Digital Extender)
- ND filters (Clear, 1/8, 1/64)
- Includes Wiper, Heater and Defroster (optional Washer)
- Salt-resistant paint
- Hybrid Image Stabilizer (mechanical and optical, named DISS)
- Supports 1080/50p (2x 3G-SDI outputs)
- Special functions: Intelligent, Haze Reduction, Night Mode
- Supports PoE++
- IP control and streaming
- Compatibility with existing Panasonic remote systems
High Picture Quality
The new AW-HR140 is an integrated remote camera system that incorporates an outdoor housing, camera, lens and pantilt head. It is equipped with the same Digital Signal Processor (DSP) and 1/2.86 type full HD 3MOS sensors as the AW-HE130 which results in high sensitivity, high S/N ratio, and high resolution due to its advanced video processing.
The HR140 maintains stable shooting performance in the toughest of environments and is compatible with various outdoor environments and applications.
In addition to a sharp, fast F1.6, 20x optical zoom lens, the HR140 is equipped with an innovative 1.4x digital extender that can increase the effective focal length of the lens by 40% while delivering smooth, high resolution video.
Designed for Outdoor Use
The HR140 offers resistance to wind pressure with all functions guaranteed to operate in wind speeds of up to 15 m/s. Basic performance is maintained at wind speeds of up to 50 m/s without destruction of the camera. Aluminum and other metal parts are coated to protect against severe salt damage, enabling installation in seaside areas subject to salt air. The camera is coated with resins that give excellent heat resistance.
Thanks to a defroster, the glass does not get frozen at low temperatures down to -15ºC (5°F). Even in blizzards, snow that hits the glass surface melts off to maintain visibility. As it can be complicated to keep the lens clear in harsh environments, a lens wiper is included in the HR140.
Benefits for Installation
The AW-HR140 has adopted a newly invented stabilizing technology, using both optical and mechanical stabilization. This technology is named Dynamic Image Stabilizing System (D.I.S.S.) and enables smooth shooting outdoors with no loss of resolution.
The HR140 can be powered at 12V-24V DC. Additionally, the HR140 is supporting PoE++ for lower installation costs as it is not necessary to install an extra power supply or even a local AC outlet. By connecting to network devices that support the IEEE802.3bt draft ver.2.0 standard, power can be supplied via LAN cable.
The camera can provide power to an external device, such as an SDI-to-Fiber conversion module.
- Haze Reduction Function: reduces haze on the picture and make it easier to see the subject that is low in contrast. Strength of the effect can be adjusted manually depending on the thickness of the fog.
- DRS: Dynamic range can be increased by compressing the image signal for the extremely bright areas that are overexposed during normal shooting while maintaining contrast
- Hybrid Digital Noise Reduction (Hybrid DNR): two types of noise reduction, 2D and 3D, are used together to enable clear video capture under a wide range of lighting conditions, with minimal after-image blurring or image degradation
- Intelligent Function: automatically corrects the picture level and color temperature according to outdoor changes. It can automatically control white balance, gain, iris, shutter and ND filter
- Night Mode: in conjunction with an optional IR illuminator, the camera can deliver high-quality monochrome video in total darkness
Variety of Video Formats
The camera supports multiple output formats required for specialized applications, including 1080/50p, 1080/50i, 1080/25p and 720/50p. Remote control video capture can now be more easily performed for specialized applications such as tele-production, and scientific research.
The camera includes two 3G-SDI compatible outputs and one Genlock input. It also supports audio line input (2 channels).
Flexible IP control architecture simplifies system design and operation as up to 100 units can be controlled via IP from a single Panasonic controller. The unit is equipped with image compression and IP transmission up to 50fps, being able to transmit up to 4 video streams at different qualities.
Using an IP browser, such as Internet Explorer or Safari, it is possible to set up and control the camera from a remote location. This feature simplifies the management of cameras around a campus, or across a worldwide enterprise network. IP video monitoring and remote camera control can also be performed from mobile terminals such as an iPhone, iPad or Android devices.
Excellent Pan-Tilt Mechanism
Thanks to a highly evolved pan-tilt design, the HR140 achieves smooth and more natural movement during on-air shots. The pan-tilt head has a wide shooting range, with a pan range of ±175° and a tilt range of -30° to 210°. The unit supports suspended installation.
The newly developed pan-tilt drive provides high-speed operation at maximum 60°/s, excellent response to remote control operation, and highly precise stop control. These features combine to accurately capture fast-action sports scenes or smooth concert footage. The camera also achieves a low noise level during operation, at NC45 or less at a pan-tilt speed of 60°/s.
Compatibility with Panasonic Controllers
The AW-HR140 can be controlled from any of following Panasonic remote controllers:
- AW-RP50 and AW-RP120 (firmware upgrade is required)
- AK-HRP200 (firmware upgrade is required)
- Supports VISCA protocol via RS422 interface
There are currently no key services available.
There are currently no other services available.
|Power Requirements||DC 12 V to 21.8 V (DC IN connector) DC 42 V to 57 V (PoE++ power supply)|
|Current Consumption||3.1 A to 5.5 A (DC IN connector) 1.2 A (PoE++ power supply)|
|Ambient Operating Temperature||-15 °C to 45 °C (5 °F to 113 °F) (preheating is required when -5 °C (23 °F) or less)|
|Ambient Operating Humidity||10% to 100% (no condensation)|
|Storage Temperature||-20 °C to 55 °C (-4 °F to 131 °F)|
|Storage Humidity||10% to 95% (no condensation)|
|Mass||Approx. 9.0 kg (19.84 lb)|
|Dimensions (W x H x D)||258 mm x 357 mm x 397 mm (10-5/32 inches x 14-1/16 inches x 15-5/8 inches) (including protrusions and cable cover)|
|Finish||Silver, salt resistant coating|
|Waterproof and Dust Proof||IP65 compliant|
|Maximum Permissible Wind Speed||15 m/sec: Operates normally 50 m/sec: Operation possible 60 m/sec: No damage|
|Wiper||Installed as standard|
|Heater||Installed as standard|
|Defroster||Installed as standard|
|Controller Supported||AW-RP120G, AW-RP50, AK-HRP200G ・ It may be necessary to upgrade the version of the controller in order to support the unit. For details on upgrading, visit the support page on the following website.|
|Imaging Sensors||1/2.86-type Full-HD 3MOS|
|Lens||Optical 20x zoom/10x digital zoom, F1.6 to F3.4 (f=4.5 mm to 90 mm; 35 mm equivalent: 32.13 mm to 642.5 mm)|
|Focus||Switching between auto and manual|
|Focus Distance||Entire zooming range: 800 mm (2.62 ft) Wide end: 400 mm (1.31 ft)|
|Color Separation Optical System||3MOS|
|Minimum Illumination||2 lx (50 IRE, F1.6, 36 dB, without accumulation)|
|Horizontal Resolution||1000 TV lines Typ (Center area)|
|Gain Selection||Auto, 0 dB to 42 dB (1 dB steps) 37 dB to 42 dB is Super Gain Mode|
|Frame Mix||0 dB, 6 dB, 12 dB, 18 dB, 24 dB ・ This cannot be configured when the format is 1080/29.97p, 1080/23.98p, 1080/29.97PsF, 1080/23.98PsF, 1080/25p, or 1080/25PsF. ・ When [Iris Mode] or [Focus Mode] is set to [Auto], this cannot be set to 18 dB or 24 dB.|
|Electronic Shutter Speed | 59.94p/59.94i||1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000|
|Electronic Shutter Speed | 29.97p||1/30, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000|
|Electronic Shutter Speed | 23.98p||1/24, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000|
|Electronic Shutter Speed | 50p/50i||1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000|
|Electronic Shutter Speed | 25p||1/25, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000|
|Synchro Scan | 59.94Hz||60.15 Hz to 642.21 Hz (255 steps)|
|Synchro Scan | 50Hz||50.15 Hz to 535.71 Hz (255 steps)|
|Gamma||HD, FILMLIKE1, FILMLIKE2, FILMLIKE3 0.30 to 0.75 (Manual setting)|
|White Balance||AWB A, AWB B, ATW, 3200K, 5600K, VAR (2000K to 15000K)|
|Chroma Amount Variability||OFF, -99% to 40%|
|Scene File||Scene1, Scene2, Scene3, Scene4|
|Intelligent Functions||Auto function for each of accumulation, gain, iris, electronic shutter, ND, and ATW|
|Output Format||1080/59.94p, 1080/29.97p*1 , 1080/23.98p*2 , 1080/59.94i, 1080/29.97PsF*3 , 1080/23.98PsF*3 , 720/59.94p, 1080/50p, 1080/25p*1 , 1080/50i, 1080/25PsF*3 , 720/50p|
|Synchronization System||Internal/External synchronization (BBS/Tri-level sync)|
|Line Input Audio In 1/2 | Input Impedance||High impedance|
|Line Input Audio In 1/2 | Input||2 channels, XLR balanced input ・ Input signal level: +4 dBu/0 dBu/-20 dBu (selectable in menu) ・ Volume variable range: -40 dB to +12 dB (can be changed in 1 dB steps in the menu)|
|Line Input Audio In 1/2 | Output||・ 4 channels, superimposed over SDI output ・ Embedded audio output level: FS-12 dB: -12 dBFS, FS-18 dB: -18 dBFS, FS-20 dB: -20 dBFS (selectable in menu) ・ Sampling frequency: 48 kHz (synchronized to video) ・ Quantization bit rate: 24-bit (LPCM) ・ Audio compression format (IP): G.726, AAC-LC (High quality)|
|Input Connector | 12V In||XLR connector|
|Input Connector | G/L In||BNC connector ・ BBS (Black Burst Sync), tri-level sync supported ・ Locking to a subcarrier is not possible with BBS.|
|Input Connector | Audio Input||mini XLR connector (line input) #1: INPUT1 Common, #2: INPUT1 HOT, #3: INPUT1 COLD, #4: INPUT2 Common, #5: INPUT2 HOT, #6: INPUT2 COLD|
|Video Output | HD-SDI Out||SMPTE424/SMPTE292 standards 75 Ω (BNC x 2) ・ OSD output is possible from the SDI OUT 1/PM connector but not from the SDI OUT 2 connector.|
|Input/Output Connector | LAN||LAN connector for IP control/video output/audio output/ PoE++ power supply PoE++ (IEEE802.3bt Draft ver.2.0 standard)|
|Input/Output Connector | RS-422||CONTROL IN RS-422A|
|Input/Output Connector | EXT||#1: DC GND, #2: HOT, #3: COLD, #4: 12V-OUT|
|Pan-Tilt Head Unit|
|Installation Method||Stand-alone (Desktop) or suspended (Hanging) ・ To ensure safety, the unit must be secured using the mount bracket supplied.|
|Camera/Pan-Tilt Head Control | IP Connecting Cable||・ When connecting through a PoE++ hub: LAN cable*4 (category 5e or above, straight cable), max. 100 m (328 ft) ・ When a PoE++ hub is not used: LAN cable*4 (category 5 or above, straight cable) max. 100 m (328 ft)|
|Camera/Pan-Tilt Head Control | AW Series Connecting Cable/Standard Protocol Connecting Cable||LAN cable*4 (category 5 or above, straight cable), max. 1000 m (3280 ft)|
|Pan/Tilt Operation Speed||Maximum speed 60°/s or higher|
|Panning Range||±175° ・ For suspended installations, the positions of the pins that determine the movement range must be changed.|
|Tilting Range||-30° to 210° ・ Depending on the pan or tilt position, the camera may be reflected in the image. ・ For suspended installations, the positions of the pins that determine the movement range must be changed.|
|Quietness||60°/s (NC45 or less)|
|Vibration Correction||D.I.S.S. (Dynamic Image Stabilizing System)|
|Accessories||Hexagonal bolt M8 × 30 mm: 4 M8 washer : 4 Spring washer: 4 Cable cover : 1 Washer nozzle mount bracket: 1 Drop-prevention wire : 1 Drop-prevention wire mounting screw (with hexagonal socket, for unit) M4 × 10 mm : 1|
|Note||*1: Native output *2: Over 59.94i output *3: For 1080/25PsF, 50i may be displayed on the monitor screen. Furthermore, for 1080/23.98PsF and 29.97PsF, 59.94i may be displayed on the monitor screen. *4 Use of an STP (shielded twisted pair) cable is recommended. ・ When connecting directly to a controller without an Ethernet hub, use a cross cable.|